Sunday, May 25, 2008

Ups Downs and Roundabouts

Well, it has been an interesting week.

We finally came to an arrangement over the transport and the Heinkel and Troll have finally been shipped as of Friday 22 May. It will take approximately two weeks for them to arrive. I'm very excited.

So that was the good news. But on all other fronts it's been a terrible week. Firstly - and of course this has nothing to do with scooters - but work has been a real mess. There is a pall of gloom hanging over my work at the moment as the main project I am on continues to descend in disaster. Political forces are preventing me and my co-project manager taking the steps we need to resolve the problems and get back on track. It's all very disheartening.

To add to my woes I dropped my bike during a lesson for my motorcycle license. How embarrasing! As soon as we hit the road it started to belt down with rain - the first time I'd even ridden in the wet and as we came to a roundabout I locked the front wheel and stacked it big time. Fortunately the most damage was done to my pride. I walked away with a scrape on the knee. The bike was okay too. But it shook my confidence a little driving on the wet roads. Oh well, could have been much worse.

And to add to my sense of gloom - the Vespa is f-cked again. The indicators haven't worked since I got the bike back from Sam. Following his advice I replaced the dodgy old battery and replaced all the globes - three were broken. But as soon as the bulbs were fitted, suddenly the wiring went. Only the right hand turn signals would work and they did not pulsate at all. Occasionally when I turned the handlebars hard left the left lights would come on which indicates to me the wiring was compromised when the front end was replaced. Sam and I had had a conversation about that after I picked up the bike and he'd indicated quite clearly this was not a job he was keen to take on so I'd already been planning to do it myself. Today (Sunday) I began taking apart the indicator switch and looking at the wiring. To be frank, it's pretty f-cking rubbish. As soon as the wires disappear inside the tubing the nice new wiring is superceded by what is clearly worn out old sh-t wiring, amateurishly twisted together. It'll undoubtedly all have to be replaced.

But that's the least of my worries.... no sooner had I started work today than the bloody engine failed. I don't know what's wrong with it now. It seems to be the same problem as before. It simply won't turnover. Given that the bike has done only one very short trip to the petrol station and back since I got it and has been turned over every three or four days while I tried to track down the wiring fault, you can understand I'm not very happy.

The German bikes were always intended to replace the Vespa eventually. The question is, what the hell am I going to do with the bike? The electrics are just an inconvenience. I can fix that myself, but if the engine is going to break down every couple of months I'm never going to be able to sell it. You live and learn maybe.

Saturday, May 17, 2008

1963 IWL Troll review


As briefly reported in Issue 1/1963, the first new "Troll l" scooter rolled off the assembly line of VEB Industriewerk Ludwigsfelde in January. The scooter "Berlin", which is an integral part of our street scene, has been replaced by a new development which offers considerably more in terms of driving comfort, driving performance, and driving safety. The starting point for this new development were demands for improved suspension, seating position and easier maintenance and repair options. In-depth studies of the city scooter "Berlin" showed that further development of the design was exhausted and a completely new development was necessary. To ensure trouble-free use, the greatest possible degree of standardization with the motorcycles of the VEB motorcycle factory in Zschopau was decisive for the technical design.

1. Frame
For the designers in Ludwigsfelde, guiding the choice of the chassis was the good experience that MZ has with the full-swing chassis of the large ES types (in addition, small types like the ES 125/150, were under development in Zschopau). This resulted in the design with front and rear long swing arms and the utilization of the shock absorbers of the ES 125/150 for the scooter "Troll l". In addition to the exceptional driving characteristics, this also has an economic benefit for our economy, which confirms the correctness of standardised development. With the spring travel of 100 mm for the rear wheel and 130 mm for the front wheel, the "Troll l" is at the top of all known vehicles of the same type.

The backbone of the new vehicle is a welded sheet metal frame that is manufactured in-house using our own welding systems. The basic profiles are welded in one operation by a modern multi-spot welding machine. This results in an absolute guarantee of flawless processing quality and economical production times. The front carrier, which comes from the MZ ES 125/150, and the rear body carrier are made of cast iron. The rear body support is also designed as a fender. The extremely torsion-resistant frame together with the hydraulically damped long swing arm suspension provide excellent driving characteristics of the "Troll l".

2. Motor
The MZ motors ES 125, ES 150 and RM 150/1 represent the modular series of the new standard motor. The RM 150/1 scooter motor is the only one equipped with a cooling fan. The performance of these motors could be further improved with further systematic development. Among other things, the connecting rod was improved with the use of a cage-guided needle bearing. The main bearings are externally lubricated by the gear oil from the clutch chamber, with the crankshaft seals now being located directly on the lifting discs. The alternator side is closed with a seal on the outside. The compensating holes required in the full lifting disks were sealed with plastic plugs to increase the pre-compression. To improve the thermal stability, light alloy composite cast cylinders with cast-in grey cast iron bushings are used, which are manufactured according to the Alfer method. The excellent heat dissipation for this type of cylinder enables operation with 0.03 mm piston clearance.

With the use of VK "Extra" (OZ 78) and the improved shape of the combustion chamber, the compression ratio could be increased to 9: 1, so that the RM 150/1 scooter engine now delivers 9.5 HP at a speed of 5500 rpm. Maximum torque is 1.25 kpm at 4000 rpm (Fig. 2). Intake and exhaust silencers have been carefully matched to the engine; the exhaust silencer especially has been completely redeveloped. The normal driving state diagram in Fig. 3 shows the gradation. The ratio of the primary chain drive has been changed to relieve the multi-disc clutch running in an oil bath. A new material is used for the primary chain, which guarantees a mileage of 25,000 km.

The housing cover shape was changed on the alternator side. Now you can get to the alternator by loosening just one screw and removing a small additional cover, which is particularly pleasant for making small adjustments on the way. The alternator is now vented through a plastic hose directly into the intake silencer.

3. Shape design and details
The rear hood has a modern three-part design, with quick-release, removable large side panels ensuring effortless access to the drive unit. Pictures 4 and 5 show the rear part with the side shells removed. The leg mudguards are high and wide and provide optimal dirt and weather protection. A comfortable, wide seat enables every driver to find the right seat position. It can be folded up to gives access to the control for the fuel tap. The fuel tank cap is also located under the seat. Other important details are the folding side stand and the exhaust completely hidden beneath the running board. Injuries from the hot exhaust, such as have previously occurred with the "Berlin" are therefore completely avoided.

There is a lockable box immediately behind the leg guards (Fig. 6). It offers plenty of space for storing tools, spares, etc. In addition, the anti-theft device, which is activated by a push button, is placed in this box.

The scooter "Troll 1" has become slightly higher than its predecessor "Berlin". This resulted from the large spring travel and the need to ensure sufficient ground clearance. However, the seating position is still within normal limits compared to other vehicles of the same type, although the slightly higher seating position is pleasant when driving. It gives the driver the impression of sitting on a motorcycle and gives extremely good contact with the road.

The accessories that are available commercially, such as luggage racks, unicycle trailers, etc., add to the vehicle’s versatility. The spare wheel is no longer supplied as standard but can be purchased as required. This fulfills numerous customer requests that reject the standard spare wheel as unnecessary ballast. In addition, it was found in tests of the frequency of breakdowns that a tyre puncture only occurred on average every 20,000 km, so that the constant carrying of a spare wheel did not appear to be necessary. An air pump is supplied as standard and is located in the upper part of the rear hood. Cautious drivers still have the option of taking their spare wheel with them.

The "Troll " is the first motor scooter with the asymmetrical dipped beam as standard! With a power consumption of 45/40 W and a light exit diameter of 136 mm, illuminating conditions of the road surface which were previously unknown in two-wheelers. Furthermore, this scooter has a flashing light and high-performance handlebar turn signals (15 W) as standard. A brake, tail and license plate light with a 95 mm light emission completes the electrical equipment.

4. Mileage
The powerful engine gives the vehicle a top speed that is still unknown in this class. With a max = 90 km/h, the character of the “Troll” touring scooter is a quick and easy way to cover long distances.

The equally high torque ensures fast driving and fast acceleration. Conditions that bring the well-known great advantages to a two-wheeled vehicle in road traffic. 60 km/h are achieved from a standing start after 11.6 seconds and 80 km/h after 23 seconds. The fuel consumption is shown in Figure 7. Fuel consumption for regular road use has a favorable value of 3 to 4.41 / 100 km. The extremely rigorous testing of the "Troll 1", which was carried out in a non-stop three-shift operation in 1961 and 1962, demonstrates the maturity of this design and the quality of the product of vehicles produced. Finally, we explain how the name "Troll" came about. This name is the summary of the first letters from the word combination "Touring-roller-Ludwigsfelde". It is to be hoped that the "Troll" confirms itself as the good spirit of its owners.

This is my English translation of the 1963 KFZ review of the IWL Troll. The original can be found here: https://dkwautounionproject.blogspot.com/2020/06/1963-kraftfahrzeugtechnik-volume-2.html


Come with me for a quick walk around my 1964 IWL Troll scooter.

For more information about these interesting East German scooters and the restoration story of my example, check out the blog posts here: https://heinkelscooter.blogspot.com/search?q=IWL+Troll